噴筆系列及配件 AIRBRUSHES & ACCESSORIES
-
必要時可拆除1、2、3、4的零件，使用工具清洗液浸泡將漆料完全洗淨。/ If necessary, part 1/2/3/4 can be removed and thoroughly cleaned with tools cleaner.
-
每次噴筆使用後，請使用對應溶劑十耐溶劑尼龍筆帶掉多餘漆料或顏料，反覆清洗2-3次，並搭配(1A)噴帽漱洗1-2次，即可完成清洗工作。/ Every time finished using the airbrush, please use a proper thinner and a thinner-resistant nylon brush to remove any paint residue. Repeat the steps 3~4 times. To finish the cleaning process, attached the Needle Cap (1A) and back-flush the airbrush 1~2 times.
-
如使用1B、1C噴嘴，需要進行漱洗，可輕微旋開2號零件，不需要全部拆除，即可逹到漱洗效果。/ To back-flush when Needle Cap 1B/1C is attached, simply loosen the Nozzle Cap (2) first. Do not detach the Nozzle Cap completely.
-
噴杯內若有殘餘顏料不可將噴針抽出，確認噴杯內清潔完成後，如欲清洗噴針，請旋開12號尾桿，將11號回定螺絲旋開，小心退除噴針，將溶劑滴於衛生紙輕輕擦拭 ，小心裝回！/ Do not remove the needle when there is still paint left in the paint cup. Make sure the paint cup is thoroughly cleaned first. Afterwards, to clean the needle, remove the Tail Cap (12) and loosen the Needle Stop Screw (11). Now the needle can be carefully removed. Gently wipe the needle on a clean tissue with some thinner. Reinsert the needle back into the airbrush carefully afterwards!
-
噴針撞歪將會影響噴筆霧化方向與效果，需特別小心。/ Exercise with extra caution. Damaging the needle may affect atomization and spray quality.
-
切勿將整把噴筆泡入溶劑或是工具清洗液體清洗。/ Never soak the whole airbrush into thinner or tools cleaner.
-
噴筆清洗後，仍會有極少的顏料殘留於漆杯或是噴針上，如固化後仍有機率發生噴嘴漆料堆積，洗筆後在噴杯內加少許溶劑後，蓋上噴杯蓋，放置12小時後將殘餘溶劑噴除，可預防堵槍現象，進而達到不需拆除噴嘴的效果。/ Even with regular general cleaning, a tiny trace of paint residue may still exist in the cup or on the needle. This may result in dried paints building up inside the nozzle. Every time after cleaning, leave a little bit clean thinner in the airbrush and put the cup's lid on for 12 hours. Afterwards, spray out all the thinner from the cup. This will effectively minimize the chance of the nozzle clogging, and therefore minimize the need to remove the nozzle for cleaning.
-
1A傳統型圓柱保護帽:持保護帽可有效保護噴針並且可以方便漱洗，但長期使用可能會有積漆，若出現此現象可單獨卸下清洗。/ Standard Round Needle Cap: This needle cap protects the needle effectively and is convenient for doing back-flush. However, over time paint may accumulate around the rim. Should this occur, simply remove and clean the needle cap.
-
1B多孔式錐度保護帽:孔洞設計可有效減緩積漆現象也可有效保護噴針，建議平常噴塗使用此款保護帽，須注意漱洗時需要轉開2號零件才能漱洗。/ Perforated Needle Cap: The holes on the wall minimize paint from accumulating, while the cap protects the needle effectively. Recommend using this cap for everyday use. Please note part (2) must be loosen before doing back-flush.
-
1C定距式保護帽:近距離等距噴塗時使用，可有效控制距離，須注意漱洗時需要轉開2號零件才能漱洗。/ Fixed Distance Needle Cap: Use this cap when it is necessary to maintain a steady and short distance from the canvas. The cap helps to maintain that distance effectively. Please note part (2) must be loosen before doing back-flush.
-
零件20、21為微調壓閥藉由轉動21號零件，可調整出漆壓力藉而控制所需要的噴塗漆量。/ Part (20/21) are the MAC Valve. By turning part (21), you can adjust the volume of air going through the airbrush, and in turn adjust the volume of paint.
-
14號板機下方內部有潤滑油，請勿使用工具清洗液清洗。/ There is lubricant underneath the Trigger. Do not clean that area with tools cleaning.
-
官方清洗影片教學請至 / For official airbrush cleaning tutorial, visit: https://www.youtube.com/c/MADWORKS01
-
售後服務維修保姜請寫信至官方信箱 / For after sales service, please email: madworks01@gmail.com
-
噴筆0.2x/0.3/0.35/0.5代表噴嘴口徑，口徑愈小的筆，愈適合拿來精緻細噴，口徑愈大的噴筆，適合大面積平噴，選撣對的口徑噴筆，將可以大量降低噴筆拆除保養機率，只需要平常清洗乾淨即可。/ 0.2x/0.3/0.35/0.5 describes the size of an airbrush nozzle. Smaller nozzles are suitable for finer details. Larger nozzles are suitable for a wider spray application. Using the right airbrush reduces the need to dissemble the airbrush for thorough cleaning; a general cleaning will be sufficient.
-
0.2x用途：細噴光影，細線，精緻塗裝。/ 0.2x is suitable for: highlights and shadings, small lines, and fine details.
-
米0.3用途： 般通用，平噴，薄噴最適合剛接觸模型的玩家。/ 0.3 is suitable for: general use, flat toning, and mist layers. Perfect for beginners.
-
0.35用途:適用於平噴薄噴，也可使用在噴金屬漆（漆料粒子顆粒較大），金油／保護漆（乾燥後硬度較硬），底漆（黏性較高）。/ 0.35 is suitable for flat toning and mist layers. Also suitable for metallic paints (bigger pigment), varnishes/protective top coats (harden when cured), and primers (higher adhesion strength).
-
0.5用途：，大面積平噴，噴金屬漆（漆料粒子顆粒較大），金油／保護漆（乾燥後硬度較硬），底漆（黏性較高）。/ 0.5 is suitable for: large surface area, metallic paints (or paints with larger pigments), varnishes/protective coatings (harden when cured), primers (higher adhesion strength)
-
不同性質的漆料或顏料，若是清洗不乾淨，有機會在噴嘴固化造成堵塞，切記每次使用後，必須確實清洗乾淨。/ When using the same airbrush for different types of paints, it is important to properly clean the airbrush between each use. Paint residue left in the nozzle may turn into gunk or dried paints, clogging the airbrush as a result.
-
漆料濃度若比例不當將會影響噴塗，若發生噴塗不順楊請優先檢査顏料稀釋比例，也可使用清水或是純溶劑噴塗測試。/ Paints not reduced to a proper consistency will affect the spray quality. If the airbrush does not spray smoothly, take a look at the thinning ratio first. Testing with plain water or thinner is another way to pinpoint where the problem is.
-
噴漆氣壓小時，顏料或漆料較容易固化於前端，尤其是颳克力顏料，如發生輕微卡槍，請進行簡易清洗動作後再績噴。/ When airbrushing at lower psi, especially with acrylic paints, it is easy for dried paints to buildup at the tip of the needle. Should tip-dry happen, simply do a quick cleanup before continue.
-
官方網站 / Official Website: https://www.madworks.tw/